3com 3800 Manuel d'utilisateur Page 90
- Page / 182
- Table des matières
- DEPANNAGE
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
5-12 CHAPTER 5: VIRTUAL LANS (VLANS)
Table 5-1 describes the commands used to configure a VLAN.
VLAN Configuration
Examples
The following example creates a port-based VLAN named accounting,
assigns the IP address 132.15.121.1, and assigns ports 1, 2, 3, and 6 to
it:
create vlan accounting
config accounting ipaddress 132.15.121.1
config accounting add port 1-3,6
Because VLAN names are unique, you do not need to enter the
keyword “vlan” after you have created the unique VLAN name. You
can use the VLAN name alone.
Table 5-1 VLAN Configuration Commands
Command Description
create vlan <name> Allows you to create a named VLAN.
create protocol <protocol_name> Allows you to create a user-defined protocol.
config protocol <protocol_name> add
<protocol_type> <hex_value>
Allows you to configure a protocol filter. Supported
protocol types include:
■ EtherType
■ LLC
■ SNAP
config vlan <name> ipaddress <ipaddress>
{<mask>}
Allows you to assign an IP address and an optional
mask to the VLAN.
config vlan <name> [add | delete] port
<portlist> {tagged | untagged}
Allows you to add and delete ports within the
VLAN. You can specify tagged and untagged
port(s). By default, ports are untagged.
config vlan <name> protocol
[<protocol_name> | any]
Allows you to configure a protocol-based VLAN. If
the keyword “any” is specified, then it becomes
the default VLAN. All packets that cannot be
classified into other protocol-based VLANs are
assigned to the default VLAN of that port.
config vlan <name> tag <vlanid> Allows you to assign a numerical VLANid. The
valid range is from 1 to 4095.
config dot1p ethertype <ethertype> Allows you to configure an IEEE 802.1Q
EtherType. Use this command if you have another
Switch that supports 802.1Q, but uses a different
EtherType. The default value used by the Switch is
8100.
SW3800.BK Page 12 Tuesday, May 5, 1998 5:20 PM
- VCCI Statement 3
- Information To The User 3
- ECHNICAL 11
- PECIFICATIONS 11
- ROUBLESHOOTING 11
- ■ Local Area Networks (LANs) 13
- ■ Ethernet concepts 13
- ■ IP Routing 13
- Finding 14
- Information in This 14
- Table 1 Notice Icons 15
- Table 2 Text Conventions 15
- Command Syntax 16
- Line-Editing 17
- Related 17
- Publications 17
- 6 ABOUT THIS GUIDE 18
- SWITCH 3800 OVERVIEW 19
- Dual-homed 21
- Network 23
- Switch 3800 Front 25
- Table 1-2 Switch 3800 LEDs 26
- Switch 3800 Rear 27
- INSTALLATION AND SETUP 29
- Installing the 30
- Switch 3800 30
- Connecting 32
- Equipment to the 32
- Console Port 32
- Cable connector: 9-pin female 33
- ACCESSING THE SWITCH 37
- Table 3-1 Default Accounts 38
- Methods of 40
- Managing the 40
- Using Telnet 3-5 41
- Table 3-2 Supported MIBs 45
- Table 3-3 Supported Traps 45
- Checking Basic 48
- Connectivity 48
- ■ Configuring autonegotiation 49
- Load Sharing 3-15 51
- Table 3-8 Port Commands 53
- COMMANDS 55
- 4-2 CHAPTER 4: COMMANDS 56
- Command History 59
- Substitution 59
- General Switch 61
- User Account 62
- Switch Management 63
- Table 4-7 VLAN Commands 64
- Table 4-8 Protocol Commands 65
- Table 4-9 FDB Commands 65
- Table 4-10 Port Commands 66
- Table 4-11 PACE Commands 67
- Table 4-12 STP Commands 68
- Table 4-14 IP ARP Commands 71
- IP Route Table 72
- Table 4-17 RIP Commands 74
- Configuration and 77
- Image Commands 77
- HAPTER 4: COMMANDS 78
- VIRTUAL LANS (VLANS) 79
- Marketing 81
- Switch 1 82
- Switch 2 82
- Accounting Engineering 83
- = All other traffic 87
- <hex_value> 88
- Configuring VLANs 89
- ■ EtherType 90
- Displaying VLAN 91
- ■ Status for each port 92
- ■ Protocol information 92
- ■ IP address 92
- ■ STPD information 92
- Deleting and 93
- Resetting VLANs 93
- SWITCH FORWARDING 95
- Configuring FDB 97
- Displaying FDB 97
- Removing FDB 98
- SPANNING TREE PROTOCOL (STP) 99
- ■ Initialization 101
- ■ Stabilization 101
- ■ Reconfiguration 101
- Spanning Tree 102
- Spanning Tree Domains 7-5 103
- STPD 1 STPD 2 104
- STP Configurations 7-7 105
- Sales & Engineering 106
- Enabling STP on 108
- Displaying STP 110
- Settings 110
- Disabling and 112
- Resetting STP 112
- IP UNICAST ROUTING 113
- HAPTER 8: IP UNICAST ROUTING 114
- ■ Static routes 115
- Configuring IP 116
- Unicast Routing 116
- Verifying the IP 117
- Configuration 117
- Configuring 117
- DHCP/BOOTP Relay 117
- (continued) 118
- Routing 122
- = IP traffic 123
- = NetBIOS traffic 123
- Displaying Router 124
- Resetting and 125
- Disabling Router 125
- STATUS MONITORING AND 127
- Port Statistics 9-5 131
- Configure logging options 136
- Reset logging options 136
- Display the log 136
- Clear the log 136
- RMON 9-13 139
- ■ 30-second intervals 140
- ■ 2-hour intervals 140
- Table 9-6 Event Actions 141
- SOFTWARE UPGRADE AND BOOT 143
- Boot Option 145
- Commands 145
- SAFETY INFORMATION 147
- PPENDIX A: SAFETY INFORMATION 148
- ■ CLASS 1 LASER DEVICE 149
- L’information de 150
- Sécurité Importante 150
- Wichtige 154
- Sicherheitsinformat 154
- TECHNICAL SPECIFICATIONS 159
- TROUBLESHOOTING 161
- Using the 162
- Command-Line 162
- Interface 162
- PPENDIX C: TROUBLESHOOTING 164
- TECHNICAL SUPPORT 167
- PPENDIX D: TECHNICAL SUPPORT 168
- Support from Your 169
- Network Supplier 169
- Returning Products 171
- GLOSSARY 173
- 2 GLOSSARY 174
- 4 GLOSSARY 176
- LIMITED WARRANTY 181
Produits connexes et manuels pour Accessoires pour ordinateurs 3com 3800
(8 pages)
(152 pages)© 2020, manymanuals.fr. Tous droits réservés | 0.989 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels